Amateur radio revision notes
Free revision notes for every lesson of the Foundation, Intermediate and Full courses: the key points and an exam-style question for each. Lessons marked “Free lesson” are complete, with the video.
Foundation · Section 1: Licensing and station identification
- 1Your Foundation licence: what it allows, call signs and locatorsWhat the amateur licence is for, where it applies, the three licence levels, your call sign and regional locator, and keeping your licence valid.
- 2On the air: identification, supervision and who you may talk toHow and when to give your call sign, who may use your station, who you may talk to, and why messages must never be secret.
- 3Interference, logs, EMF and Schedule 1What Ofcom can require if your station causes interference, when you must keep a log, the EMF safety rules, and how to read Schedule 1 in the exam.
Foundation · Section 2: Technical basics
- 4Electricity: current, circuits, Ohm's law, power and batteriesConductors and insulators, what a circuit needs, Ohm's law, power in watts, polarity and batteries, with simple calculations.Free lesson
- 5AC, frequency and wavelength, analogue and digitalDirect and alternating current, the frequency ranges of mains, speech and radio, HF, VHF and UHF, working out wavelength, and analogue and digital signals.
Foundation · Section 3: Transmitters and receivers
- 6Transmitters: modulation and the transmitter block diagramHow a transmitter puts information onto a radio carrier, AM, FM, SSB and CW, the stages of a simple transmitter, and how to avoid causing interference.
- 7Receivers and software defined radioHow a receiver recovers information, the stages of a simple receiver, and how software defined radios do the same job in software.
Foundation · Section 4: Feeders and antennas
- 8Feeders, connectors and matching: coax, baluns, SWR and the ATUCoaxial and twin feeder, why feeders lose power, baluns, connectors, and how to check and correct the match between your antenna and transmitter.
- 9Antennas: types, polarisation, patterns, gain and ERPWhat an antenna does, polarisation, the common antenna types, radiation patterns, gain, and how to work out ERP.Free lesson
Foundation · Section 5: Propagation
- 10Propagation: how far signals go, from HF to UHFHow radio waves travel, how the ionosphere carries HF signals around the world, and what sets the range at VHF and UHF.
Foundation · Section 6: Electromagnetic compatibility
- 11EMC: how interference happens and how to cure itWhat EMC and immunity mean, which modes cause most trouble, how RF gets into other equipment, and the cures, including the dummy load test.
- 12A good neighbour: antenna siting, RF earths, vehicles and complaintsSiting antennas to avoid interference, why a station needs an RF earth, fitting radios in vehicles, and handling a neighbour's complaint.
Foundation · Section 7: Operating practices
- 13Making a contact: listening, calling, phonetics, reports and logsHow to find a clear frequency, make a CQ call, use the phonetic alphabet and suffixes, give a signal report, keep a log, and behave on air.Free lesson
- 14Band plans, repeaters, digital modes, satellites and going abroadReading a band plan, sharing the spectrum, using repeaters, digital voice, connecting other equipment, satellites, and operating abroad.
Foundation · Section 8: Safety
- 15Electrical safety: mains, fuses, RCBOs and batteriesThe dangers of high voltage and high current, wiring a mains plug, fuses and RCBOs, working inside equipment, what to do after an accident, and battery safety.
- 16A safe station: tools, soldering, antennas, height, RF exposure and working outdoorsUsing tools and soldering safely, putting up antennas and using ladders, RF exposure, lightning and power lines, and safety when operating outdoors.
Intermediate · Section 1: Licensing and station identification
- 1Your Intermediate licence: privileges and responsibilitiesWho may use your station and how, operating from ships and aircraft, and when you may pass messages for other people and organisations.
- 2Licence conditions: interference, logs, remote control, EMF and Schedule 1What happens if your station causes interference, when you must keep a log, the rules for remote and unattended operation, when the EMF rules apply, and how to read Schedule 1.
Intermediate · Section 2: Technical aspects
- 3Resistors: series, parallel, potential dividers and source resistanceOhm's law with milli and kilo, combining two or three resistors, the potential divider, tolerances, and why a battery's voltage drops under load.Free lesson
- 4Capacitors and inductors: how they work and how they combineWhat capacitance and inductance are, what increases them, the series and parallel formulas for each, polarised capacitors and tuning slugs.
- 5Alternating current: sine waves, RMS, phase and reactanceThe sine wave, period and frequency, phase, RMS and peak values, and how capacitors and inductors oppose alternating current in opposite ways as frequency changes.
- 6Frequency and wavelength, RF on conductors and digital signalsConverting between frequency and wavelength, why current and voltage vary along an antenna wire, and how sampling turns an analogue signal into a digital one.
- 7Transformers and tuned circuits: resonance, impedance and QHow a transformer steps voltage up or down, what happens when a capacitor and inductor resonate, how series and parallel tuned circuits behave, and what Q tells you about selectivity.
- 8Filters: low pass, high pass, band pass and notchThe four filter types, their circuits and response curves, the cut-off frequency, and how filters stop a transmitter radiating harmonics.
- 9Semiconductors: diodes, transistors, amplifiers, oscillators and ICsHow a diode conducts, the varicap diode, the bipolar transistor as an amplifier and a switch, biasing, crystal and variable oscillators, and integrated circuits.
- 10Power supplies: cells, batteries, rectifiers and regulatorsCell voltages and battery capacity, half-wave, full-wave and bridge rectifiers, smoothing with a reservoir capacitor, and linear versus switched-mode supplies.
Intermediate · Section 3: Transmitters and receivers
- 11Modulation: AM depth, FM deviation and single sidebandDepth of modulation, peak deviation, narrow and wide band FM, how single sideband is made and why it's efficient, and which modes use the least bandwidth.
- 12Inside a transmitter: oscillators, stability, DDS and amplifier efficiencyThe block diagrams of CW, AM, SSB and FM transmitters, crystal versus variable oscillators, how to keep an oscillator stable, digital synthesis, and how to work out amplifier efficiency.
- 13Clean transmissions: harmonics, key clicks and chirpWhere harmonics come from and who they bother, why fast keying causes key clicks and how to shape it, and what causes chirp and how to cure it.
- 14Receivers: sensitivity, selectivity and the superhetCrystal sets and direct conversion receivers, sensitivity and overload, selectivity and its limits, the superhet and its intermediate frequency, detectors for each mode, and AGC.Free lesson
- 15Software defined radio: time and frequency domainsHow an SDR uses the Fourier transform, what the time and frequency domains show, simple spectra of harmonic waves, and the blocks inside a software defined radio.
Intermediate · Section 4: Feeders and antennas
- 16Feeders, baluns, SWR and matchingBalanced and coaxial feeders, characteristic impedance, feeder loss in decibels, choke baluns, standing waves, and what an antenna matching unit can and can't do.
- 17Antennas: patterns, gain, EIRP, Yagis and trapsRadiation patterns in three dimensions, front-to-back ratio and beamwidth, isotropic gain and EIRP, the angle of radiation, feed point impedance, the Yagi and the trap.
Intermediate · Section 5: Propagation
- 18Propagation: ground wave, the ionosphere and VHFGround, space and sky waves, polarisation, the ionospheric layers and what changes them, MUF and LUF, skip, hops, fading, long path, sporadic E and multipath.Free lesson
Intermediate · Section 6: Electromagnetic compatibility
- 19EMC: immunity, how interference gets in, and the curesWhat electromagnetic compatibility means, how amateur signals and household devices interfere, direct pick-up and broadband amplifiers, and the cures: filters, ferrites, common-mode chokes and the dummy load test.
- 20Station layout, RF earths and mobile installationsConnecting the station to minimise EMC problems, what a good RF earth is, where not to put a transmitting antenna, and installing a radio safely in a vehicle.
Intermediate · Section 7: Operating practices
- 21Operating: prefixes, awards, band plans, data modes, satellites and operating abroadInternational prefixes, awards and contests, the IARU band plan rules, Q codes, computer data modes, working through satellites, and why the Intermediate licence doesn't travel.
Intermediate · Section 8: Safety
- 22Safety: stored charge, fuses, batteries, tools, EMF and lightningDischarging capacitors, choosing the right fuse, live working, vehicle batteries, safe use of hand and power tools, EMF distances at 100 watts, and static protection.
Intermediate · Section 9: Measurements and construction
- 23Measurements and construction: meters, decibels, colour code and solderingUsing a multimeter correctly, voltmeters and ammeters, measuring power, decibel arithmetic with 3 and 10 dB, dBW, dBi and dBd, the resistor colour code and markings, screening and soldering.
Full · Section 1: Licensing
- 1The Full licence: messages, interference, Schedule 1 and coordinationWhat you may send and to whom, codes and encryption, the law on offensive messages, clean transmitters, Ofcom's role, and reading Schedule 1 and the Notice of Coordination.
- 2EMF compliance: assessments, public areas, records and emergenciesWhere the EMF limits come from, who counts as the general public, where they may be, how to carry out an assessment, what records to keep, and the emergency exemption.
Full · Section 2: Technical aspects
- 3Resistor networks, power and toleranceSolving series and parallel resistor networks for current, voltage and power, the three power formulas, and how component tolerances affect a circuit.
- 4Capacitance, charge, inductance and time constantsWhat sets a capacitor's value, charge and the coulomb, dielectrics and breakdown voltage, self-inductance and back EMF, and time constants in CR and LR circuits.
- 5Reactance, phase, impedance and couplingPhase in inductors and capacitors, calculating reactance, capacitors for coupling and decoupling, RF chokes, and impedance in series CR and LR circuits.Free lesson
- 6Resonance, Q, dynamic resistance and crystalsFinding resonant frequency, Q and the voltages it produces, half-power points and bandwidth, dynamic resistance, and how quartz crystals resonate.
- 7Transformers, sampling and aliasingMutual inductance, the voltage, current and impedance ratios of a transformer, core materials and losses, and how sampling, aliasing and the Fourier transform work.
- 8Semiconductors: Zener diodes, biasing, amplifier types and oscillatorsZener diodes, biasing bipolar and field effect transistors, the three amplifier configurations, amplifier classes, and what keeps an oscillator going.
- 9Power supplies: stabilisers, PIV and switch modeStabilising circuits with Zener diodes, pass transistors and ICs, the peak inverse voltage rectifiers must survive, and how a switch mode supply works.
Full · Section 3: Transmitters and receivers
- 10SSB and FM transmitters: modulation index, bandwidth and multipliersFM modulation index and sidebands, SSB and FM transmitter block diagrams, frequency multipliers, and calculating the bandwidth of AM, SSB and FM signals.
- 11Oscillators and synthesisers: drift, PLL and DDSWhy drift matters, how a phase locked loop synthesiser works and sets its step size, direct digital synthesis, and how synthesisers can go off frequency.
- 12RF power amplifiers: linearity, classes, peak power and ALCWhich modes need linear amplifiers, how distortion creates harmonics and intermodulation, the parts of a PA, rating for different modes, and ALC.
- 13Unwanted emissions: over-modulation, harmonics, intermodulation and parasiticsHow over-modulation and over-driving widen a signal, driving external amplifiers, avoiding harmonics and mixer products, and curing parasitic and self-oscillation.
- 14The superhet in depth: mixers, image frequency and IF stagesThe superhet and double superhet, mixer products, choosing the local oscillator, calculating the image frequency, high and low IFs, and IF transformers and gain control.Free lesson
- 15Receiver performance: dynamic range, preamps, phase noise, demodulators and AGCHow overload creates intermodulation, dynamic range, phase noise, when a preamplifier helps, how AM, CW, SSB and FM demodulators work, and AGC attack and decay.
- 16SDR, I and Q, transceivers and transvertersPhasors, I and Q signals and how SDR demodulates any mode, direct sampling, what transceivers share, RIT, and using transverters safely.
Full · Section 4: Feeders and antennas
- 17Feeders and matching: velocity factor, return loss, AMUs and quarter-wave transformersVelocity factor and electrical length, balun types, SWR and return loss, how feeder loss hides a mismatch, matching units, and the quarter-wave transformer.
- 18Antenna lengths, current and voltage, and feed point impedanceCalculating practical dipole and vertical lengths with an end factor, current and voltage along an antenna, and the feed point impedances of common antennas.
Full · Section 5: Propagation
- 19Propagation: field strength, MUF, NVIS, EME, aurora and link budgetsHow field strength falls with distance, E and H fields and circular polarisation, the Sun's effects, critical frequency and MUF, NVIS, EME, aurora, galactic noise and link budgets.
Full · Section 6: Electromagnetic compatibility
- 20How interference happens: blocking, cross-modulation, rectification and imagesWhy installation affects immunity, your EMC responsibilities, non-compliant equipment, blocking and cross-modulation, passive intermodulation, rectification, masthead amplifiers, IF and image interference.
- 21Curing interference: filters, field strength, bonding, vehicles and complaintsFilters and stubs, mains and braid-breaking filters, why ferrite rings stop common-mode current, calculating field strength, RF bonding, balanced antennas, vehicle installations and handling complaints.
Full · Section 7: Operating practices
- 22Operating: split frequencies, 5 MHz and 472 kHz, ITU regions and CEPTWhy stations work split, testing for interference, the 5 MHz and 472 kHz band plans, band plans abroad, the three ITU regions, and operating overseas under CEPT and HAREC.Free lesson
Full · Section 8: Safety
- 23Safety: PME, live working, lightning, risk assessment and generatorsLethal voltages, PME earthing and the RF earth, live working, RF exposure, lightning, temporary and mobile operation, risk assessments and generator safety.
Full · Section 9: Measurements and construction
- 24Test equipment: meters, SWR bridges, oscilloscopes and spectrum analysersMultipliers and shunts, how meters load circuits, source and load impedance, how SWR meters work, reading an oscilloscope, and what a spectrum analyser shows.
- 25Measuring power and frequency, decibels and temperature effectsFrequency measurement accuracy near band edges, crystal calibrators, counters and standard frequencies, measuring RF power and PEP, decibel calculations, and temperature effects on components.